Thin sheet metal and plastic
Thin sheet metal comes in many materials, and the right choice depends on the environment and what the part needs to withstand. Here we go through the materials we offer, how they differ and when to choose sheets, rolls or material by the metre. You’ll find our full range under Material.
Choose your material
| Material | Grade | Properties | Typical uses |
|---|---|---|---|
| Cold-rolled steel | DC01 | Cost-effective and easy to form and cut. Rusts, so store dry or oiled. | Alignment and spacing in dry environments, machine building, prototypes |
| Stainless steel | 1.4301 / 1.4307 | Good corrosion resistance in normal environments | Food industry, interiors, general industry |
| Acid-resistant stainless steel | 1.4404 | Contains molybdenum, giving better resistance to chlorides, salt and chemicals than standard stainless | Marine environments, chemical and process industry, outdoor use |
| Stainless spring steel | 1.4310 | High strength, springs back, stainless | Springs, contact strips, clips |
| Brass | CuZn37 (CW508L) | Easy to form, good corrosion resistance, decorative finish | Electronics, model making, spacers |
| Aluminium | 99.5% Al, soft and hard | Lightweight with good thermal and electrical conductivity. The hard version is stiffer. | Heat dissipation, lightweight structures |
| Thin plastic sheets | – | Colour-coded by thickness, electrically insulating, will not corrode | Insulation, simple alignment |
Rule of thumb: If you just need something cost-effective for a dry environment, choose cold-rolled steel. For moisture or water: stainless. For salt, chlorine or chemicals: acid-resistant. If the part needs to spring back: spring steel.
Stainless or acid-resistant?
Acid-resistant stainless steel (1.4404) contains molybdenum, which makes it more resistant to chlorides such as seawater, pool water and certain chemicals. For normal indoor environments, standard stainless steel (1.4301) is usually enough, and it costs less.
Sheets, rolls or by the metre?
- Sheets: ready-made sizes that are easy to store. Ideal when you need smaller pieces.
- Rolls: for cutting many parts or long strips.
- By the metre: order exactly the length you need.
- Self-adhesive: sheet metal with adhesive backing that sticks directly to the surface. Available in cold-rolled steel, stainless steel and brass.
Laminated shim – adjust the thickness on site
Laminated shim consists of many thin foil layers bonded into a single sheet. You peel off one layer at a time with a knife until you reach exactly the right thickness. This makes it ideal for adjustments during assembly, when the exact dimension isn’t known in advance. Available in aluminium, brass, cold-rolled steel and stainless steel.
Thin plastic sheets
Our thin plastic sheets are colour-coded, so you can see the thickness at a glance. Plastic is electrically insulating and does not corrode, making the sheets well suited to insulation and simple alignment.
Frequently asked questions
Which material should I choose for my application?
It mainly depends on the environment. Cold-rolled steel is cost-effective for dry conditions. Stainless steel withstands moisture and water, and acid-resistant stainless also handles salt and chemicals. Spring steel suits parts that need to spring back, and plastic is the choice when you need electrical insulation. See the table further up the page.
What is the advantage of laminated material?
You can adjust the thickness right there during assembly by peeling off one layer at a time. You don’t need to know the dimension in advance or keep several thicknesses in stock.
What thicknesses are available?
We offer material from 0.008 mm. Available thicknesses depend on the material and format. You select the thickness on each product.
What widths are available?
Width depends on the material and on whether you buy sheets, rolls or material by the metre. Available dimensions are shown on each product.
Can I get widths other than standard?
Yes, in many cases we can cut to other widths. Send us an inquiry with material, thickness, width and quantity, and we’ll get back to you.
Need something else?
We can often cut or manufacture to size, for example finished shims made to your drawing. Read more about manufacturing or send us an inquiry with material, thickness, dimensions and quantity.